Відео

Wait -- "... that's the way Festool keeps the cost of their power tools down ...". You're kidding, right?

Flammy!

What brand of countersink bit is that at 12:55? Haven’t seen one with a spring before.

Anyone in the comment section has any thoughts on the Diablo blades?

I really do enjoy your nerding out on all things woodwork! Clearly significant research goes into your content development and preparation. I appreciate the work you put into this, thank you.

The third tip was the cut supposed to be slanted? I guess they are just demoing and not trying to produce a straight line?

Thanks!

😂 on watch the new stuff

I lost almost my entire first joint of my middle finger on a jointer I was rushing also

How do these compare to the Milwaukie 18v track saw?

Bullsh*t commercial. Overpriced products. Aluminum? It should be precisely made.

Great, practical test. Great netrics. Cubitron is the clear winner. I’ve come to ignore the winers who complain that you need to buy an interface pad. Whatever. Cubitron still gets the job done; faster, cheaper & longer. Thanks for supporting/ recommending Taylor Toolworks. They’re one of my favorite vendors.

I've always seen tusked mortise and tenon with a slight bevel to the mortis and a matching bevel on the wedge (to tightly pull things together with the wedging force). Is this angled mortise and wedge the same thing, or is it technically a different joinery technique/style all together? Thanks, I just learned to cut the wedged mortis and tenon from an old book, but this straight angle looks a heck of a lot easier to get right than a 7-degree bevel on the inside of one wall of a mortis.

A word of warning about using this type of jig, if the bandsaw blade drifts off line from the template and the width of the offcut widens the tension creted inside the tooth section of the guide will snap your blade! this happened to me first time out cutting a quarter inch strip of a 3/4 inch panel … the drift was only about 3/16" before its snapped my new and expensive 1/2" blade!!

Perhaps a truss across the bottom that would mate to a dog hole clamp or a hold fast?

Anyone know if the app is still being worked on? Bought it on android, but shows it's not compatible with my s24 ultra

Great video! For ripping ¾" plywood at a 45 degree angle, wanting a clean cut but avoid burning, what would you suggest? (I am getting burning with my 40 tooth ATB blade from Ridge Carbide)

I took a square piece of scrap 2x4 and clamped it on top of the board I was cutting to fence one side of the saw and with my free hand held another fence face down on the other side of the saw to guide those teeth home for squared perfection. Magnets are ingenious though. Definitely looks like a fun build. Wish I had more time for WW!!! Gonna quit my job now 😅

We'll pretend we didn't see you screw up the first glue up @5:40 of the large fence 😅 Great tool dude!

I have that same Ridgid trim router trim and made these jigs for it, and they work great.

If you were to sell this it would be so hard to even put a price on for the amount of time it takes

1,200psi for Maple??? Highly doubtful. "Dale Zimmerman of Franklin International, maker of Titebond woodworking glues, recommends 100 to 150 pounds per square inch (psi) for clamping softwoods and 175-250 psi for hardwoods." I think that the people that make wood glues and do exhaustive destructive testing of likely thousands of wood glue joints on lots of wood varieties know the proper amount of pressure required.

OK, My name is James the One Handed Maker and I have a Sawstop for obvious reasons. Never set it off but as you will see in my videos I use the table saw a lot and it's, well.... just peace of mind knowing if something goes wrong I have less chance of serious injury. Regards James One Handed Maker - Australia

Pretty USELESS table saw for when I need to ration my supply of hotdogs 😒

@katzmosestools - Thanks for breaking this down in a very digestible explanation. Love the content. I got it down to .0001 !

I have to disagree with you about not doing your eyeliner in it, as I must say wood chisels are far better than traditional mirrors. I actually found a community, 5,000 strong whom all believe mirrors are against their religion. Thanks for the beauty product review. ..... 😂

Just because you dont find it necessary to strive for perfection, does that make it wrong for those who do?

Holy shit! Dude! Holy Shit! Thank you!

Nice jig. Question, what brand drill bit with stops did you use in this video?

I want to make the 1 1/2" edge of some 2x4 studs flat. Lose the rounded edges. What plane should I use? I have a Stanley #4 now.

If it’s a true finger save you can send the brake in to saw stop to be tested and they will replace it for free.

😂

great video and very helpful, but I had to move the speed to .75 so I could understand you. Probably just me being old...

I just bought the other day a Bosch gkf 550 palm router and i am just eager to try it!Love your video sir :D

I have this stop block this is the best on the market

Nice review, thanks!

Looks good enough to me.

Wow! Truly incredible work

lol....@3:30 there's literally a "Scratch on the hotdog"😒

Thanks for this awesome vid! I’ve been intimidated by the thought of cutting dovetails for decades and now I’m pretty excited to give them a try, especially with this beautiful use of contrasting walnut & maple to make inlayed DT’s. Thanks again!

Wish I would’ve never saw this pointless video amongst many others pumping the safety stops on saws. The best plan is to pay attention and keep your fingers and hands away from any fast moving blades. If you think you might need one of these. Get rid of your table saw. Sorry but people have been successful with sawing things for years and years before these things were invented. If you don’t have the experience or confidence to not have one then don’t have one.

2:50 Metric is no BS also.

Dang my drill press only goes to 610 RPM at the lowest speed. Time to upgrade, or is there another option?

This is good advice. I have the LN 62, LN 64, LN #4, two LN block planes a LN #7. 10 LN altogether, I love them all.

Great idea and next level by put virtual boards on the cutouts

I ordered one and have been waiting on it, went back to the link and people have been using and reviewing it already. When will mine ship?

Degrees make this demo confusing, demo the 5 cut so we as buyers know how it stack up to a $140.oo buy . . . nice product just skeptical. . .prove me wrong I don't think U can Good luck way to many variables

Is there a video where you go over how you build that fence extension?